At a Glance
- A gas, not a liquid: Dimethyl ether is a colourless gas at normal conditions, shipped liquefied under its own vapor pressure.
- Two routes: Methanol is made first and then dehydrated, or syngas is converted directly. Sources disagree on which is better.
- Recycling is built in: One academic indirect design converts about 80% of the methanol per pass, then recycles the rest.
- Feedstocks: Natural gas, coal or biomass, usually through syngas and methanol.
- Main uses: Aerosol propellant, a diesel alternative in specially designed engines, and a chemical intermediate.
- Buyer takeaway: DME ships as a flammable gas (UN1033), so check the grade, the SDS and the container type first.
What You’ll Learn
This guide explains how dimethyl ether is produced, which properties affect handling, where it is used, and what to check when sourcing it.
Introduction
Dimethyl ether production starts from methanol or syngas, and the process shapes what a supplier can deliver. That matters more here than for most solvents, because dimethyl ether is a gas and ships liquefied under pressure.
This guide explains the two production routes, the raw materials behind them and the properties that drive handling. It then covers the main uses and the checks that matter when you buy. Where sources disagree, we say so. Figures from design studies are labelled as such. It also flags where public information is thin, so you know what to confirm with a supplier.
It is written for procurement teams, formulators and plant staff. Many already understand methanol production and now need the next step in that chain.
What Is Dimethyl Ether?
The dimethyl ether formula is CH₃OCH₃, also written C₂H₆O. Its structure is a single oxygen atom joined to two methyl groups. The CAS number is 115-10-6.
At normal conditions it is a colourless gas with a faint ethereal odour. It is shipped as a liquefied gas under its own vapor pressure. The sections below cover how it is made and where it is used.
Dimethyl Ether Production Routes: Indirect and Direct
Two routes make dimethyl ether at industrial scale. The indirect route first makes methanol, then dehydrates it. The direct route converts syngas to DME without a separate methanol step.
The Alternative Fuels Data Center lists biomass, methanol and fossil fuels as feedstocks. It describes the direct route as syngas from natural gas, coal or biomass, and the indirect route as methanol dehydration.
| Route | Steps | Catalyst and conditions (as reported) | Trade-off |
| Indirect (two-step) | Syngas to methanol, then methanol dehydration to DME and water | Acid catalyst. One design preheats feed to 250 °C at about 15 atm. | More units, but each step is optimised on its own. |
| Direct (one-step) | Syngas converted straight to DME | One catalyst system doing both jobs | Skips methanol isolation. A liquid-phase version is still in development. |
The direct-route row reflects general references, not a design study. Sources disagree on which route is better. General references say both are commercial, and that the two-step route is simple with lower start-up cost.
A technology licensor favours the indirect route because each reactor can be tuned and heat is easier to remove. Some summaries call the direct route more efficient, but we found no design data to support that. Treat the choice as plant-specific.
The Indirect Route: From Methanol to DME
In the indirect route, methanol loses water over an acid catalyst to form dimethyl ether. The reaction is 2 CH₃OH → CH₃OCH₃ + H₂O. One academic design case sizes a plant at 50,000 tonnes a year of 99.5 wt% DME.
That design runs these steps:
- Feed crude methanol, mixed with recycled methanol.
- Preheat the feed to about 250 °C.
- React it in an adiabatic packed-bed reactor.
- Take DME as the overhead product of the first column.
- Remove impurities such as acetaldehyde and acetone in a second column.
- Recover methanol in a third column and recycle it.
Why Recycling Is Needed
The reactor outlet in this design is about 366 °C, and the catalyst deactivates above about 400 °C. Temperature must therefore be controlled throughout the bed.
Conversion is about 80% per pass, even though equilibrium for pure methanol exceeds 92%. The reactor is limited by kinetics, so unreacted methanol is separated and recycled. These are one design’s numbers. Real plants differ by producer and catalyst.
The Direct Route From Syngas
The direct route combines methanol synthesis and dehydration, so syngas becomes DME without isolating methanol. One catalyst system has to do both jobs, which is the main design challenge.
Public data on commercial direct plants is limited, because technology licensors hold most of the detail. Buyers rarely need the route itself. They need the specification and the documents that prove it.
Feedstocks and Raw Materials
Dimethyl ether can be made from natural gas, coal or biomass, because each can be turned into syngas. Methanol is the intermediate in the indirect route. The Alternative Fuels Data Center notes that natural gas is the likely feedstock for large-scale US production.
Methanol availability therefore sits upstream of DME supply. For the methanol side, see industrial methanol uses. Elchemy prices DME per kilogram, against grade, volume, packaging and destination.
Properties of Dimethyl Ether That Matter for Handling
Handling rules follow from a few dimethyl ether properties. Dimethyl ether boils at about -24 °C, so it is a gas at room temperature. Its vapor is about 1.6 times heavier than air, so a leak sinks to low spots.
The table lists the values most buyers ask about. They come from NOAA CAMEO Chemicals and the Alternative Fuels Data Center. Published flammable limits and autoignition values differ between sources, so read them from your supplier’s SDS.
| Property | Value | Why it matters |
| Formula and CAS | CH₃OCH₃ (C₂H₆O), 115-10-6 | Identification on SDS and orders |
| Boiling point | About -24 °C | Gas at room temperature |
| Vapor density | About 1.6 times air | Sinks and pools in low areas |
| Liquefaction | About 75 psi to stay liquid | Needs pressurised storage |
| Transport | UN1033, Class 2.1 flammable gas | Flammable-gas shipping rules |
Industrial Uses of Dimethyl Ether
The main dimethyl ether uses are as an aerosol propellant, a fuel and a chemical intermediate. Elchemy’s product page also lists solvent and refrigerant use. The grade you need depends on the job.
The Alternative Fuels Data Center describes DME as a diesel alternative for specially designed compression ignition engines. It has about half the energy density of diesel, so the tank must be twice as large. The vehicle also needs a fuel system built for DME.
| Use | Role of DME | Grade to ask about |
| Aerosol products | Propellant | Aerosol-propellant grade |
| Chemical synthesis, solvent and refrigerant | Intermediate, solvent or refrigerant | Industrial or technical grade |
| Fuel | Diesel alternative in designed engines | Fuel grade |
Confirm the grade against your own specification before ordering. To discuss grade and volume, Request a Quote.
Safety, Storage and Transport
Dimethyl ether is a flammable gas shipped as a liquefied gas. CAMEO lists it under UN1033, and contact with the liquid can cause frostbite. The gas can also asphyxiate by displacing air.
The Alternative Fuels Data Center says handling is similar to propane, with pressurised storage tanks at ambient temperature. Check storage and transport rules in sections 7 and 14 of the SDS, and read our chemical hazards guide. For why the SDS matters when buying, see SDS in procurement. Qualified EHS review is required before you plan storage.
Sourcing Dimethyl Ether: Producers, Manufacturers and Suppliers
Plants are built around methanol or syngas supply, so buyers usually purchase through suppliers and distributors. Dimethyl ether producers run the plants, while a dimethyl ether supplier matches grade and packaging to your order.
Elchemy is a supplier and distributor, not a producer. Its product page says producers in its network are checked for purity, moisture and export compliance before onboarding. Elchemy supplies aerosol-propellant, industrial or technical, and fuel grades. Cylinders and bulk volumes are available, and COA, TDS and a GHS-compliant SDS are standard. REACH and market-specific documents are available on request.
Use these rules when you shortlist:
- Choose cylinders if you are qualifying material or running small lots.
- Choose bulk if you have recurring volume.
- Choose aerosol grade for propellant filling, and fuel grade for engine use.
The same checks apply whether you compare dimethyl ether manufacturers or distributors. Our guide to manufacturers versus distributors sets out the trade-offs. The supplier selection checkpoints list what to verify.
Plan delivery early, using our note on lead-time planning. To qualify material first, Request a Sample.
FAQs
Which grades does Elchemy supply?
Elchemy supplies aerosol-propellant, industrial or technical, and fuel grades of dimethyl ether. The product page lists no grade specification values. Share your application and the grade you need. The team will quote against your specification rather than a generic listing.
Is dimethyl ether supplied in cylinders or in bulk?
Both. Elchemy supplies cylinders and bulk volumes for aerosol, industrial and synthesis buyers. Minimum order and packaging vary with the application, so share your requirement. The team will then confirm exact figures and lead time in the quote before you commit.
Which documents come with an order?
A certificate of analysis, TDS and a GHS-compliant SDS are standard with every order. REACH and market-specific documents are available on request. Export documentation covers your destination market, so tell the team where the material is going when you ask for pricing.
How is dimethyl ether priced?
Elchemy prices dimethyl ether per kilogram. The price varies with grade, volume, packaging (cylinders or bulk) and destination. The team gives a live quote against your specification, not a fixed list price. The product page says quotes follow within 24 business hours.
Which purity checks matter?
Ask for purity and moisture on the certificate of analysis, since Elchemy checks producers on both. In the academic design case, a second column removes impurities such as acetaldehyde and acetone from crude methanol. Confirm the assay and moisture limits for your grade.
Can I get a sample before ordering?
Elchemy’s product page promises domestic samples within 24 to 48 hours. For other destinations, samples are supplied where feasible. Because DME is a flammable gas, share your delivery location and handling capability. The team can then confirm what is possible.
Conclusion
Dimethyl ether is made by two routes, and both start from methanol or syngas. For buyers, the route matters less than the grade, the documents and the handling rules for a flammable gas.
Use this guide to ask better questions, then judge a supplier on grade fit, packaging and compliance support. That keeps the conversation on what you will actually receive. Elchemy sources aerosol-propellant, industrial and fuel grade DME against your specification. Share your grade, quantity and destination, and the team will confirm packaging and next steps. Request a Quote.








